- 您现在的位置：买卖IC网 > Sheet目录995 > NCL30051LEDGEVB (ON Semiconductor)BOARD EVAL NCL30051 LED DRIVER
NCL30051
R 1 ) R 2
V PFC + V PREF @ ) I PFB @ R 1
R 2
(eq. 5)
A transconductance amplifier has a voltage ? to ? current
gain, gm. That is, the output current is controlled by the
differential input voltage. The NCL30051 amplifier has a
typical gm of 95 m S. The PControl pin provides access to the
amplifier output for compensation. The compensation
network is ground referenced allowing the PFC feedback
signal to be used to detect an overvoltage condition.
The compensation network on the PControl pin is
selected to filter the bulk voltage ripple such that a constant
control voltage is maintained across the ac line cycle. A
capacitor between the PControl pin and ground sets a pole.
A pole at or below 20 Hz is enough to filter the ripple
voltage for a 50 and 60 Hz system. The low frequency pole,
f p , of the system is calculated using Equation 6.
V PCS(ILIM) . This comparison is done on a cycle by cycle
basis. The overcurrent threshold is typically 0.84 V.
The current sense signal is prone to leading edge spikes
caused by the power switch transitions. The NCL30051 has
leading edge blanking circuitry that blocks out the first
110 ns (typical) of each current pulse.
PFC Driver
The PFC driver source and sink impedances are typically
60 and 15 W , respectively. Depending on the external
MOSFET gate charge requirements, an external driver may
be needed to drive the PFC power switch. A driver such as
the one shown in Figure 9 can be easily implemented using
small bipolar transistors.
VCC
f p +
gm
2 p C PControl
(eq. 6)
where, C PControl is the capacitor on the PControl pin to
ground.
A key feature to using a transconductance type amplifier,
is that the input is allowed to move independently with respect
to the output, since the compensation capacitor is connected
to ground. This allows dual usage of the feedback pin by the
error amplifier and by the overvoltage comparator.
xDRVx
To gate
of MOSFET
PFC Undervoltage
The NCL30051 safely disables the controller if the PFB
pin is left open. An undervoltage detector disables the
controller if the voltage on the PFB pin is below
V PUVP(low) , typically 0.23 V. A 1.2 m A (typical) pull down
current source, I PFB , ensures V PFB falls below V PUVP(low)
if the PFB pin is floating. The PFB pull down current source
affects the PFC output voltage regulation setpoint.
PFC Overvoltage
An overvoltage detector monitors the PFC feedback
voltage and disables the PFC driver if an overvoltage
condition is detected. This is set internal to the IC at 5%
above the nominal setting of the PFC voltage If an OVP
event is detected, drive pulses are suppressed until the over
voltage condition is removed. The overvoltage detector
tolerance is better than ± 2%. The overvoltage detector
threshold, V POVP , is the midpoint between the PFC driver
disable and enable thresholds. The overvoltage comparator
hysteresis is the voltage difference between the disable and
enable thresholds. An overvoltage condition is detected
Figure 9. External Driver
Half ? Bridge Driver
The half ? bridge stage operates at a fixed 50% duty ratio.
The oscillator frequency is divided by two before it is
applied to the half ? bridge controller.
The half ? bridge controller has a low side driver,
HDRVlo, and a 600 V high side driver, HDRVhi. The built
in high voltage driver eliminates the need for an external
transformer or dedicated driver. A built ? in delay between
each drive transition eliminates the risk of cross
conduction. The delay is typically 785 ns. The typical duty
ratio of each half ? bridge driver is 48%.
The high side driver is connected between the HBoost
and the HVS pins as shown in Figure 10.
VCC
D boost
HBoost
once V PFB exceeds V POVP by half of V POVP(HYS) . The
controller is re-enabled once V PFB drops below V POVP by
half of V POVP(HYS) .
PFC Overcurrent
The PFC current is monitored by means of an overcurrent
detector. The PCS pin provides access to the overcurrent
HDRVhi
HVS
C boost
detector. The PFC drive pulse is terminated if the voltage
on the PCS pin exceeds the overcurrent threshold,
http://onsemi.com
14
Figure 10. Half ? bridge High Side Driver
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
NCL30100ASLDGEVB
BOARD DEMO SGL LAYER PWM DIM LED
NCL30105GEVB
BOARD EVAL 80V 350 FOR LED DRV
NCP1013LEDGEVB
BOARD EVAL 5W UNIV LED DRIVER
NCP1028LEDGEVB
EVAL BOARD FOR NCP1028LEDG
NCP1216AFORWGEVB
BOARD EVAL NCP1216A 35W
NCP1351LEDGEVB
EVAL BOARD FOR NCP1351LEDG
NCP3065BBGEVB
BOARD EVAL NCP3065 MR16 BOOST
NCP3066SCBCKGEVB
EVAL BOARD FOR NCP3066SCBCKG
相关代理商/技术参数
NCL30080
制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Quasi-Resonant Primary Side Current-Mode Side Current-Mode
NCL30080_13
制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Quasi-Resonant Primary Side Current-Mode Controller for LED Lighting
NCL30080A
制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Quasi-Resonant Primary Side Current-Mode Controller for LED Lighting
NCL30080ASNT1G
功能描述:LED照明驱动器 Quasi-Res I-Mode Cntlr
RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
NCL30080B
制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Quasi-Resonant Primary Side Current-Mode Controller for LED Lighting
NCL30080BSNT1G
制造商:ON Semiconductor 功能描述:PRIMARY SIDE CC FOR LED L - Tape and Reel
NCL30081
制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Dimmable Quasi-Resonant Primary Side Current-Mode Controller for LED Lighting
NCL30081_13
制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Dimmable Quasi-Resonant Primary Side Current-Mode Controller for LED Lighting